Underfloor Heating

Underfloor heating uses the whole floor as the emitter, so it performs at the low flow temperatures heat pumps produce most efficiently — with no visible emitters anywhere in the room.

Discuss Your Project +44 7596 452547

01DistributeFlow and return manifolds feed continuous zoned circuits across each floor area.
02RadiateThe floor slab releases warmth evenly across the room.
03ControlZone actuators and thermostats hold each area at its setpoint.

How it works

Radiant warmth at low flow temperatures

A sealed wet system: continuous pipe circuits run from a flow and return manifold on each floor, with actuators and thermostats holding every area at its own setpoint.

What you gain

Ideal partner for heat pumps
No radiators or visible emitters
Even temperatures with no cold spots
Quiet and maintenance-free in use

What we deliver

Room-by-room heat loss and circuit design
Screed, low-profile and joisted floor systems
Manifold location, pipe layout and pressure testing
Zone actuators, wiring centres and thermostats
Screed drying and commissioning programmes
Balancing and flow rate verification

Typically suited to

New builds, deep refurbishments and any project pairing underfloor heating with a heat pump.

Completed work

Underfloor heating installations

Foil-faced underfloor heating panels with blue pipe across an open-plan room — Completed low-profile system across an open-plan living space, screed-ready with bi-fold access retained.

Large floor area covered with red underfloor heating pipe loops — Large open-plan floor plate laid out with continuous circuits at design pipe centres.

Red underfloor heating loops covering a steel-framed floor plate — Full-floor circuit layout through a steel-framed residence, coordinated around every partition.

White underfloor heating pipes clipped over foil-faced insulation across a wide room — Wide first-fix layout over foil-faced insulation with clipped returns and even spacing.

Spiral underfloor heating coil in a room with metal stud partitions — Spiral and serpentine circuits set out room by room in a metal-stud residence.

Blue underfloor heating pipework installed across a ground floor under construction — First-fix underfloor circuits across a full ground floor during structural fit-out.

Red underfloor heating pipes tied to reinforcement mesh over a membrane — Reinforcement-mesh installation with tight, uniform loop returns before the screed pour.

Dense red underfloor heating loops over insulation in a glazed room — Continuous circuits laid at close centres to lift output in a high-glazing room.

Orange underfloor heating pipe held in a black castellated floor panel — Castellated panel system holding pipe securely at consistent centres.

Castellated underfloor heating panels with orange pipe laid up to a window wall — Castellated boards taken tight to the perimeter for even floor temperatures at the glazing.

Red underfloor heating pipe loops clipped to mesh over floor insulation — Clipped pipe circuits set out over insulation and reinforcement mesh before screeding.

Blue underfloor heating pipes laid at even spacing over foil-faced insulation — Consistent pipe centres and clean returns over foil-faced insulation.

Underfloor heating circuits routed through rooms of a building under construction — Zoned circuits routed room by room ahead of screed pour.

Blue underfloor heating pipe loops in a hallway routed around a staircase — Hallway circuits routed neatly around the staircase with grouped flow and return tails.

Red pipe coil on a decoiler beside installed underfloor heating loops — Pipe decoiler positioned mid-floor to run continuous joint-free loops.

Pipe decoiler with coil of underfloor heating pipe on insulation boards — Pipe decoiler feeding continuous loops onto insulation boards — no joints below the screed.

White underfloor heating pipe loops installed over insulation in a refurbishment — Low-profile installation over insulation in a refurbishment, ready for screed.

Two stainless steel underfloor heating manifolds with circulation pumps in a plant area — Twin stainless manifolds with pumps, mixing sets and labelled circuits serving ground floor zones.

Close-up of underfloor heating manifold flow meters and labelled circuits — Flow meters and return valves on a labelled eight-port manifold, ready for balancing.

Plant room with insulated copper pipework, MVHR unit and underfloor heating manifolds — Plant room integration: insulated pipework, MVHR unit and underfloor manifolds coordinated in one space.

How we work

Design to commissioning, one accountable contract

01
Design
Heat loss and load calculations, system selection, plant room layout and coordination with the architect and structural team.
02
Specification
Equipment selection, schematics, pipework and duct routing, and a costed mechanical package.
03
Installation
First fix through second fix by our own engineers, sequenced with the main contractor's programme.
04
Commissioning
Balancing, flow rates, controls setup, F-Gas checks and performance verification across every system.
05
Handover & Support
O&M documentation, client demonstration, and ongoing servicing and maintenance.

Related services

Air Source Heat Pumps

Air source heat pumps extract low-grade heat from ambient air and lift it to a usable flow temperature for hea…

Ground Source Heat Pumps

Ground source heat pump systems draw heat from the stable temperature below ground, giving the highest seasona…

Smart Controls & Building Integration

Controls tie every mechanical system together so heating, cooling and ventilation cooperate rather than compet…

Underfloor Heating

Radiant warmth at low flow temperatures

What you gain

What we deliver

Typically suited to

Underfloor heating installations

Design to commissioning, one accountable contract

Design

Specification

Installation

Commissioning

Handover & Support

Related services

Air Source Heat Pumps

Ground Source Heat Pumps

Smart Controls & Building Integration